NEWS
Home » News » Product News » CMC in Ceramic Glazes: How to Improve Suspension, Application, and Green Strength

CMC in Ceramic Glazes: How to Improve Suspension, Application, and Green Strength

Author: Arella Sun     Publish Time: 2026-11-17      Origin: Unionchem

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

Quick answer: Carboxymethyl cellulose (CMC) is used in ceramic glazes to help control slurry handling and improve the strength of the unfired glaze layer. It can support more consistent application by modifying viscosity and helping the deposited glaze remain attached during handling. But CMC is not a universal cure for settling, cracking, or poor adhesion: its performance depends on the glaze composition, water content, addition method, application process, and firing schedule.

The right purchasing decision is not “Which CMC has the highest viscosity?” It is which grade provides the required glaze performance at an acceptable dosage without creating mixing, drying, or firing defects.

Terminology: CMC usually refers to sodium carboxymethyl cellulose in commercial ceramic applications. Confirm the exact material and grade on the supplier’s technical data sheet.

CMC in Ceramic Glazes: Grade Selection & Troubleshooting

What Does CMC Do in a Ceramic Glaze?

A ceramic glaze is a suspension of mineral and other solid ingredients in a liquid, commonly water, before it is applied and fired. Its behavior must remain suitable through storage, mixing, application, drying, and kiln processing.

CMC can contribute in three principal ways:

  1. Binding the unfired glaze layer. It can help the dried coating resist dusting and damage before firing.

  2. Modifying slurry rheology. It can affect how the glaze flows, coats a surface, and behaves during application.

  3. Supporting application consistency. By changing the liquid phase, it may help reduce some forms of segregation or uneven deposition.

These functions are related but not identical. A grade that gives strong dry-layer binding may not provide the best spraying behavior. Likewise, a glaze that appears stable in a bucket may still apply unevenly or dry with defects.

CMC is an organic processing aid. It does not replace the glaze’s mineral formulation or become a substitute for evaluating the fired surface.

CMC Grade Selection at a Glance

Glaze requirement

CMC characteristic to investigate

Finished-process test

Reduced dusting before firing

Binding performance at the effective dosage

Rub or handling test on dried glazed ware

Consistent dipping or pouring

Appropriate flow behavior

Coating weight and visual uniformity

Reliable spray application

Dispersion and viscosity suited to equipment

Nozzle behavior and deposited coating

Less settling during storage

Performance in the complete slurry

Settling and remixing after a defined hold

Fewer preparation problems

Predictable hydration and dispersion

Mixing time and lump inspection

There is no single CMC grade that is best for every ceramic glaze. Wall-tile glaze, sanitaryware glaze, engobe, and decorative applications can have different solids levels, application methods, and process targets.

Is CMC a Binder, a Thickener, or a Suspension Aid?

It may contribute to all three functions, but those labels should not be treated as guarantees.

As a binder, CMC helps the unfired glaze layer hold together after drying. This matters when ware must be moved, decorated, or handled before entering the kiln.

As a rheology modifier, CMC changes the behavior of the liquid phase. Its effect on application depends on dosage and the rest of the glaze formulation.

As a suspension aid, CMC may help improve short-term uniformity, but it does not automatically prevent dense mineral particles from settling indefinitely. Particle-size distribution, solids loading, clay content, dispersants, and storage conditions also matter. If a glaze develops a hard sediment that cannot be remixed easily, simply adding more CMC may not address the root cause.

For a related discussion of how CMC differs from other hydrocolloids, see Unionchem’s hydrocolloid selection guide.

Which CMC Specifications Matter for Ceramic Glazes?

A supplier’s quotation should identify more than the product name. Ask for the specifications and methods that affect your production process.

Solution viscosity—and how it was measured

Viscosity can help distinguish CMC grades, but values are not directly comparable unless the suppliers use equivalent methods. Request the solution concentration, water quality, preparation procedure, hydration time, temperature, instrument, and measurement setting.

A grade with a higher laboratory solution viscosity will not necessarily produce a better glaze. What matters is the result in the actual mineral slurry.

Degree of substitution

CMC grades may differ in their degree of substitution, often abbreviated DS. This is one characteristic that can affect dissolution and behavior. However, DS alone cannot predict finished-glaze performance. Compare it alongside viscosity, grade consistency, and application results.

Purity and consistency

Commercial grades can differ in composition and lot-to-lot control. For an established glaze recipe, a change in raw-material behavior may alter mixing or application even when the nominal addition rate remains unchanged. Ask for a lot-specific certificate of analysis (COA) and agree on which properties are critical to your process.

Particle size and dissolution behavior

Powder handling matters. A material that forms lumps or dissolves slowly can create uneven viscosity and defects that appear to be formulation problems. Request grade-specific preparation guidance and test it with production equipment.

How Much CMC Should Be Added to a Glaze?

There is no universal CMC dosage for ceramic glazes. The effective amount depends on the grade, whether the glaze is supplied as a powder or prepared slurry, the solids content, application method, and required dry-layer strength.

For an initial laboratory study, formulators can compare several small, increasing additions around their current recipe or supplier-recommended starting point. Define clearly whether each addition is calculated on the dry solids or the total wet slurry; confusing those two bases can produce a substantial error.

At each level, check:

  • slurry viscosity after a consistent hydration period;

  • settling and ease of remixing;

  • application weight and coating uniformity;

  • drying behavior;

  • dry-layer adhesion and dusting; and

  • fired appearance.

The preferred level is the lowest practical addition that meets the full process target. Excess CMC may increase viscosity beyond what the application equipment can handle and can introduce drying or firing-related concerns. An apparently stronger dried coating is not a successful result if the glaze then applies poorly or produces defects after firing.

CMC in Ceramic Glazes: Grade Selection & Troubleshooting

How to Add CMC Without Lumps

Poor dispersion is one of the simplest ways to lose the benefit of an otherwise suitable grade. If powder is added too rapidly, the outer surface of an agglomerate can hydrate while its center remains dry.

A controlled preparation procedure should include:

  1. A defined addition point. Decide whether CMC is introduced during glaze preparation or as a separately prepared solution, according to the grade and plant process.

  2. Adequate mixing. Add material at a rate the equipment can disperse.

  3. Consistent water quality. Use water representative of production; unexpected changes can affect the slurry.

  4. A defined hydration period. Measure and use the glaze at consistent times after addition.

  5. Inspection before application. Check for undissolved material, lumps, or changes in flow.

Do not assume that a preparation method that works for one CMC grade will work unchanged for another. If the plant is switching suppliers, compare both materials using the same equipment and process sequence.

Troubleshooting: When the Glaze Still Fails

Symptom

Possible causes

First checks

Glaze dusts or rubs off before firing

Insufficient binding; unsuitable grade; poor coating or drying conditions

Dry-layer handling test, CMC preparation, application weight

Slurry forms lumps

CMC added too fast or inadequately dispersed

Addition method, mixing energy, hydration time

Glaze settles during storage

Solids distribution or suspension system is inadequate

Particle-size distribution, solids content, dispersant system, remixing

Application layer is too thick

Excessive slurry viscosity or coating pickup

CMC level, water content, dipping or spraying conditions

Spraying becomes inconsistent

Viscosity, lumps, or equipment conditions

Slurry preparation, screening, nozzle and pressure settings

Dried glaze cracks or flakes

Coating thickness, drying conditions, substrate interaction, or formulation imbalance

Application weight and drying profile—not CMC alone

Fired surface has defects

Multiple possible causes, including glaze formulation and firing

Compare fired trials; do not assume the binder is the sole cause

Results vary between batches

Different hydration time, material lot, water, or solids content

Standardize preparation and compare lot-linked records

Diagnose the stage at which the defect first appears. A problem visible in the wet slurry calls for a different investigation from one that appears during drying or only after firing.

How to Qualify a New CMC Supplier for Ceramic Production

A successful sample test is only the beginning. To reduce production risk, use a consistent qualification process.

Step 1: Define the application

Tell the supplier whether the material is intended for a glaze, engobe, or another ceramic process. Share the application method—such as dipping, pouring, or spraying—and identify the principal problem you need to solve.

Step 2: Request technical documents

Obtain the technical data sheet (TDS), safety data sheet (SDS), sample COA, and preparation guidance for the exact offered grade. Ask which test method supports each reported viscosity value.

Step 3: Run matched laboratory trials

Compare the incumbent and candidate CMC grades in the same glaze formulation. Keep the dry solids, water, addition sequence, mixing time, and test timing constant.

Step 4: Test through firing

A wet-slurry result is not enough. Assess application, drying, unfired handling, and the fired surface. Record the kiln conditions used in the comparison.

Step 5: Validate at production scale

Confirm that the grade behaves as expected with the plant’s actual mixers, holding tanks, application equipment, and operating schedule.

Step 6: Lock the purchase specification

Agree on the grade designation, test methods, critical acceptance limits, packaging, lot traceability, and change-notification procedure. Confirm the MOQ, lead time, and quotation terms for the specific grade and order before placing a commercial purchase order.

Compare Cost per Acceptable Glazed Piece—not Price per Kilogram

A cheaper CMC may be more expensive in use if it requires a higher dosage, takes longer to dissolve, causes more rejects, or produces inconsistent application. A higher-priced grade is only justified if it provides a measurable production benefit.

When comparing suppliers, consider:

  • effective CMC addition rate;

  • preparation and mixing time;

  • glaze uniformity;

  • material lost through application defects;

  • unfired handling losses;

  • fired rejection rate; and

  • consistency across commercial lots.

The meaningful purchasing result is cost per acceptable finished piece, supported by a stable process—not merely the price of a bag of powder.

Buyer’s Checklist

Before approving CMC for a ceramic glaze, ask:

  1. What is the exact CMC grade and intended ceramic application?

  2. How is its solution viscosity measured?

  3. What information is available on degree of substitution and dissolution behavior?

  4. How should the product be added using our equipment?

  5. Has it been tested in our complete glaze, not only in water?

  6. What happens to application, drying, dry-layer strength, and fired appearance?

  7. Can the supplier provide a lot-specific COA, TDS, and SDS?

  8. How will commercial lots be traced to the approved grade and specification?

  9. What changes to the product or manufacturing process will trigger notification?

  10. What are the confirmed packaging, MOQ, lead time, and order terms?

e8878f49-c7e9-4bf5-b502-f7cb3ee6eb80.jpg

Frequently Asked Questions

Why is CMC added to ceramic glazes?

CMC is commonly used to modify slurry behavior and improve the strength of the unfired glaze layer. It may support more consistent application, but its effectiveness depends on the complete glaze formulation and process.

Is high-viscosity CMC always better for a glaze?

No. Higher solution viscosity does not automatically mean better suspension, application, or binding in the actual glaze. It may also make processing more difficult. Compare grades through complete glaze trials.

Can CMC stop a glaze from settling?

It may help manage slurry behavior, but it cannot be assumed to solve every settling problem. Dense particles, particle-size distribution, solids content, and the dispersant system also influence storage stability.

Why does my glaze still dust after adding CMC?

Possible reasons include insufficient effective CMC, incomplete dissolution, inadequate coating, or drying and handling conditions. Test the dried layer and review how the CMC was prepared before increasing its dosage.

Can I replace one supplier’s CMC with another at the same dosage?

Not without qualification. Grades can differ in viscosity, dissolution, composition, and lot consistency. Compare them in the same glaze and assess both unfired and fired performance.

Should CMC dosage be calculated on dry solids or wet slurry?

Either basis may appear in a plant’s instructions, but it must be stated explicitly and used consistently. A percentage calculated on dry glaze solids is not the same as the same percentage calculated on total wet slurry.

Conclusion

The right CMC grade helps a ceramic glaze move through storage, application, drying, handling, and firing with fewer avoidable problems. Selecting it requires more than checking a solution-viscosity figure. The strongest evaluation compares grades in the actual glaze, follows the material through the full production process, and confirms that commercial lots can reproduce the approved result.

Evaluating CMC for a ceramic glaze? Share your glaze type, application method, current CMC grade, preparation procedure, and the defect you want to solve when requesting technical documents and samples from Unionchem. Confirm grade availability and commercial terms before production approval.