Publish Time: 2026-11-17 Origin: Unionchem
Quick answer: Carboxymethyl cellulose (CMC) is used in ceramic glazes to help control slurry handling and improve the strength of the unfired glaze layer. It can support more consistent application by modifying viscosity and helping the deposited glaze remain attached during handling. But CMC is not a universal cure for settling, cracking, or poor adhesion: its performance depends on the glaze composition, water content, addition method, application process, and firing schedule.
The right purchasing decision is not “Which CMC has the highest viscosity?” It is which grade provides the required glaze performance at an acceptable dosage without creating mixing, drying, or firing defects.
Terminology: CMC usually refers to sodium carboxymethyl cellulose in commercial ceramic applications. Confirm the exact material and grade on the supplier’s technical data sheet.
A ceramic glaze is a suspension of mineral and other solid ingredients in a liquid, commonly water, before it is applied and fired. Its behavior must remain suitable through storage, mixing, application, drying, and kiln processing.
CMC can contribute in three principal ways:
Binding the unfired glaze layer. It can help the dried coating resist dusting and damage before firing.
Modifying slurry rheology. It can affect how the glaze flows, coats a surface, and behaves during application.
Supporting application consistency. By changing the liquid phase, it may help reduce some forms of segregation or uneven deposition.
These functions are related but not identical. A grade that gives strong dry-layer binding may not provide the best spraying behavior. Likewise, a glaze that appears stable in a bucket may still apply unevenly or dry with defects.
CMC is an organic processing aid. It does not replace the glaze’s mineral formulation or become a substitute for evaluating the fired surface.
Glaze requirement |
CMC characteristic to investigate |
Finished-process test |
Reduced dusting before firing |
Binding performance at the effective dosage |
Rub or handling test on dried glazed ware |
Consistent dipping or pouring |
Appropriate flow behavior |
Coating weight and visual uniformity |
Reliable spray application |
Dispersion and viscosity suited to equipment |
Nozzle behavior and deposited coating |
Less settling during storage |
Performance in the complete slurry |
Settling and remixing after a defined hold |
Fewer preparation problems |
Predictable hydration and dispersion |
Mixing time and lump inspection |
There is no single CMC grade that is best for every ceramic glaze. Wall-tile glaze, sanitaryware glaze, engobe, and decorative applications can have different solids levels, application methods, and process targets.
It may contribute to all three functions, but those labels should not be treated as guarantees.
As a binder, CMC helps the unfired glaze layer hold together after drying. This matters when ware must be moved, decorated, or handled before entering the kiln.
As a rheology modifier, CMC changes the behavior of the liquid phase. Its effect on application depends on dosage and the rest of the glaze formulation.
As a suspension aid, CMC may help improve short-term uniformity, but it does not automatically prevent dense mineral particles from settling indefinitely. Particle-size distribution, solids loading, clay content, dispersants, and storage conditions also matter. If a glaze develops a hard sediment that cannot be remixed easily, simply adding more CMC may not address the root cause.
For a related discussion of how CMC differs from other hydrocolloids, see Unionchem’s hydrocolloid selection guide.
A supplier’s quotation should identify more than the product name. Ask for the specifications and methods that affect your production process.
Viscosity can help distinguish CMC grades, but values are not directly comparable unless the suppliers use equivalent methods. Request the solution concentration, water quality, preparation procedure, hydration time, temperature, instrument, and measurement setting.
A grade with a higher laboratory solution viscosity will not necessarily produce a better glaze. What matters is the result in the actual mineral slurry.
CMC grades may differ in their degree of substitution, often abbreviated DS. This is one characteristic that can affect dissolution and behavior. However, DS alone cannot predict finished-glaze performance. Compare it alongside viscosity, grade consistency, and application results.
Commercial grades can differ in composition and lot-to-lot control. For an established glaze recipe, a change in raw-material behavior may alter mixing or application even when the nominal addition rate remains unchanged. Ask for a lot-specific certificate of analysis (COA) and agree on which properties are critical to your process.
Powder handling matters. A material that forms lumps or dissolves slowly can create uneven viscosity and defects that appear to be formulation problems. Request grade-specific preparation guidance and test it with production equipment.
There is no universal CMC dosage for ceramic glazes. The effective amount depends on the grade, whether the glaze is supplied as a powder or prepared slurry, the solids content, application method, and required dry-layer strength.
For an initial laboratory study, formulators can compare several small, increasing additions around their current recipe or supplier-recommended starting point. Define clearly whether each addition is calculated on the dry solids or the total wet slurry; confusing those two bases can produce a substantial error.
At each level, check:
slurry viscosity after a consistent hydration period;
settling and ease of remixing;
application weight and coating uniformity;
drying behavior;
dry-layer adhesion and dusting; and
fired appearance.
The preferred level is the lowest practical addition that meets the full process target. Excess CMC may increase viscosity beyond what the application equipment can handle and can introduce drying or firing-related concerns. An apparently stronger dried coating is not a successful result if the glaze then applies poorly or produces defects after firing.
Poor dispersion is one of the simplest ways to lose the benefit of an otherwise suitable grade. If powder is added too rapidly, the outer surface of an agglomerate can hydrate while its center remains dry.
A controlled preparation procedure should include:
A defined addition point. Decide whether CMC is introduced during glaze preparation or as a separately prepared solution, according to the grade and plant process.
Adequate mixing. Add material at a rate the equipment can disperse.
Consistent water quality. Use water representative of production; unexpected changes can affect the slurry.
A defined hydration period. Measure and use the glaze at consistent times after addition.
Inspection before application. Check for undissolved material, lumps, or changes in flow.
Do not assume that a preparation method that works for one CMC grade will work unchanged for another. If the plant is switching suppliers, compare both materials using the same equipment and process sequence.
Symptom |
Possible causes |
First checks |
Glaze dusts or rubs off before firing |
Insufficient binding; unsuitable grade; poor coating or drying conditions |
Dry-layer handling test, CMC preparation, application weight |
Slurry forms lumps |
CMC added too fast or inadequately dispersed |
Addition method, mixing energy, hydration time |
Glaze settles during storage |
Solids distribution or suspension system is inadequate |
Particle-size distribution, solids content, dispersant system, remixing |
Application layer is too thick |
Excessive slurry viscosity or coating pickup |
CMC level, water content, dipping or spraying conditions |
Spraying becomes inconsistent |
Viscosity, lumps, or equipment conditions |
Slurry preparation, screening, nozzle and pressure settings |
Dried glaze cracks or flakes |
Coating thickness, drying conditions, substrate interaction, or formulation imbalance |
Application weight and drying profile—not CMC alone |
Fired surface has defects |
Multiple possible causes, including glaze formulation and firing |
Compare fired trials; do not assume the binder is the sole cause |
Results vary between batches |
Different hydration time, material lot, water, or solids content |
Standardize preparation and compare lot-linked records |
Diagnose the stage at which the defect first appears. A problem visible in the wet slurry calls for a different investigation from one that appears during drying or only after firing.
A successful sample test is only the beginning. To reduce production risk, use a consistent qualification process.
Tell the supplier whether the material is intended for a glaze, engobe, or another ceramic process. Share the application method—such as dipping, pouring, or spraying—and identify the principal problem you need to solve.
Obtain the technical data sheet (TDS), safety data sheet (SDS), sample COA, and preparation guidance for the exact offered grade. Ask which test method supports each reported viscosity value.
Compare the incumbent and candidate CMC grades in the same glaze formulation. Keep the dry solids, water, addition sequence, mixing time, and test timing constant.
A wet-slurry result is not enough. Assess application, drying, unfired handling, and the fired surface. Record the kiln conditions used in the comparison.
Confirm that the grade behaves as expected with the plant’s actual mixers, holding tanks, application equipment, and operating schedule.
Agree on the grade designation, test methods, critical acceptance limits, packaging, lot traceability, and change-notification procedure. Confirm the MOQ, lead time, and quotation terms for the specific grade and order before placing a commercial purchase order.
A cheaper CMC may be more expensive in use if it requires a higher dosage, takes longer to dissolve, causes more rejects, or produces inconsistent application. A higher-priced grade is only justified if it provides a measurable production benefit.
When comparing suppliers, consider:
effective CMC addition rate;
preparation and mixing time;
glaze uniformity;
material lost through application defects;
unfired handling losses;
fired rejection rate; and
consistency across commercial lots.
The meaningful purchasing result is cost per acceptable finished piece, supported by a stable process—not merely the price of a bag of powder.
Before approving CMC for a ceramic glaze, ask:
What is the exact CMC grade and intended ceramic application?
How is its solution viscosity measured?
What information is available on degree of substitution and dissolution behavior?
How should the product be added using our equipment?
Has it been tested in our complete glaze, not only in water?
What happens to application, drying, dry-layer strength, and fired appearance?
Can the supplier provide a lot-specific COA, TDS, and SDS?
How will commercial lots be traced to the approved grade and specification?
What changes to the product or manufacturing process will trigger notification?
What are the confirmed packaging, MOQ, lead time, and order terms?
CMC is commonly used to modify slurry behavior and improve the strength of the unfired glaze layer. It may support more consistent application, but its effectiveness depends on the complete glaze formulation and process.
No. Higher solution viscosity does not automatically mean better suspension, application, or binding in the actual glaze. It may also make processing more difficult. Compare grades through complete glaze trials.
It may help manage slurry behavior, but it cannot be assumed to solve every settling problem. Dense particles, particle-size distribution, solids content, and the dispersant system also influence storage stability.
Possible reasons include insufficient effective CMC, incomplete dissolution, inadequate coating, or drying and handling conditions. Test the dried layer and review how the CMC was prepared before increasing its dosage.
Not without qualification. Grades can differ in viscosity, dissolution, composition, and lot consistency. Compare them in the same glaze and assess both unfired and fired performance.
Either basis may appear in a plant’s instructions, but it must be stated explicitly and used consistently. A percentage calculated on dry glaze solids is not the same as the same percentage calculated on total wet slurry.
The right CMC grade helps a ceramic glaze move through storage, application, drying, handling, and firing with fewer avoidable problems. Selecting it requires more than checking a solution-viscosity figure. The strongest evaluation compares grades in the actual glaze, follows the material through the full production process, and confirms that commercial lots can reproduce the approved result.
Evaluating CMC for a ceramic glaze? Share your glaze type, application method, current CMC grade, preparation procedure, and the defect you want to solve when requesting technical documents and samples from Unionchem. Confirm grade availability and commercial terms before production approval.
CMC in Ceramic Glazes: How to Improve Suspension, Application, and Green Strength
PAC vs CMC in Drilling Fluids: How to Compare Fluid-Loss Control, Rheology, and Cost-in-Use
PAC in Water-Based Drilling Fluids: How to Select PAC-LV and PAC-HV for Fluid-Loss Control
CMC vs PAC in Drilling Fluids: How to Choose the Right Fluid Loss Additive for Water-Based Muds
Xanthan Gum vs CMC vs HEC vs PAC: How to Choose the Right Hydrocolloid for Your Application
HEC in Shampoo and Personal Care: The Non-Ionic Thickener for Cationic Systems
Xanthan Gum in Cosmetics and Personal Care: How It Works and How to Use It
PAC in Hydraulic Fracturing Fluids: How Polyanionic Cellulose Works as a Fluid Loss Additive
HEC in Paints and Coatings: How Hydroxyethyl Cellulose Works as a Rheology Modifier
Welan Gum in Self-Compacting Concrete (SCC): A Formulator's Guide
CMC in Ice Cream And Dairy: How It Works And Why Formulators Use It
Xanthan Gum in Gluten-Free Baking: How It Works And How To Use It